综述文章

钎焊金刚石工具研究进展

  • 章文姣 ,
  • 孔祥清 ,
  • 曲艳东
展开
  • 辽宁工业大学土木建筑工程学院, 锦州121001
章文姣, 讲师, 研究方向为金刚石制品, 电子信箱:zhangwenjiao850321@163.com

收稿日期: 2014-11-17

  修回日期: 2015-04-07

  网络出版日期: 2015-07-15

基金资助

辽宁省教育厅科学技术研究基金项目(L2013253);国家自然科学基金项目(11302093);辽宁工业大学基金项目(X201222)

Progress in studies of brazed diamond tools

  • ZHANG Wenjiao ,
  • KONG Xiangqing ,
  • QU Yandong
Expand
  • School of Civil & Architectural Engineering, Liaoning University of Technology, Jinzhou 121001, China

Received date: 2014-11-17

  Revised date: 2015-04-07

  Online published: 2015-07-15

摘要

从钎焊材料和钎焊工艺两个方面, 综述了钎焊金刚石工具的研究现状, 探讨了钎焊技术提高金刚石工具性能的机理, 分析了当前钎焊金刚石工具研究存在的问题, 并对其今后的研究方向, 特别是对钎焊镍基孕镶金刚石工具的研发进行了展望。

本文引用格式

章文姣 , 孔祥清 , 曲艳东 . 钎焊金刚石工具研究进展[J]. 科技导报, 2015 , 33(12) : 110 -115 . DOI: 10.3981/j.issn.1000-7857.2015.12.018

Abstract

The studies of brazed diamond tools are reviewed in this paper focusing on the brazing materials and the brazing processes, and how to use the brazing technology to improve the performance of the diamond tools is discussed. Problems in the current studies of brazed diamond tools are analyzed. Some suggestions for the future research directions, especially for the nickel based brazed impregnated diamond tools, are given.

参考文献

[1] 张向红, 王艳辉. 采用镀覆金刚石的技术经济效益分析[J]. 金刚石与 磨料磨具工程, 2011, 31(3): 61-64. Zhang Xianghong, Wang Yanhui. Analysis for economic benefits of Ticoated diamonds technology[J]. Diamond & Abrasives Engineering, 2011, 31(3): 61-64.
[2] 王艳辉, 李晓虎, 常锐, 等. 金刚石微粉表面镀覆对线锯的关键作用分 析[J]. 金刚石与磨料磨具工程, 2013, 33(3): 26-30. Wang Yanhui, Li Xiaohu, Chang Rui, et al. Effect of coated diamond micro powder on diamond wire saw manufacturing technology[J]. Diamond & Abrasives Engineering, 2013, 33(3): 26-30.
[3] Yamazaki T, Suzumura A. Brazing-filler material and method for brazing diamond: US, 6889890[P]. 2005-05-10.
[4] Chattopadhyay A, Chollet L, Hintermann H. Experimental investigation on induction brazing of diamond with Ni- Cr hardfacing alloy under argon atmosphere[J]. Journal of Materials Science, 1991, 26(18): 5093- 5100.
[5] Chen S M, Lin S T. Brazing diamond grits onto a steel substrate using copper alloys as the filler metals[J]. Journal of Materials Engineering and Performance, 1996, 5(6): 761-766.
[6] 伍俏平, 邓朝晖, 潘占, 等. 钎焊气氛对金刚石钎焊性能的影响[J]. 机 械工程学报, 2012, 48(4): 51-57. Wu Xiaoping, Deng Zhaohui, Pan Zhan, et al. Effect of brazing atmosphere on brazing performance of diamond[J]. Journal of Mechanical Engineering, 2012, 48(4): 51-57.
[7] 姚正军, 徐鸿钧. Ni-Cr合金与金刚石和钢基体界面微区的分析研究 [J]. 南京航空航天大学学报, 2001, 33(4): 311-314. Yao Zhengjun, Xu Hongjun. Micro-analysis of interface between Ni-Cr alloy and diamond[J]. Journal of Nanjing University of Aeronautics & Astronautics, 2001, 33(4): 311-314.
[8] 秦喜杰, 殷声, 赖和怡. 金刚石工具胎体材料中碳化物形成元素的行 为[J]. 粉末冶金技术, 1992, 10(2): 87-91. Qin Xijie, Yin Sheng, Lai Heyi. Behavior of carbide-forming elements in matrix materials of diamond tools[J]. Powder Metallurgy Technology, 1992, 10(2): 87-91.
[9] Chattopadhyay A, Chollet L, Hintermann H. On performance of brazed bonded monolayer diamond grinding wheel[J]. CIRP Annals- Manufacturing Technology, 1991, 40(1): 347-350.
[10] Sung C M. Metal bond diamond tools that contain uniform or patterned distribution of diamond grits and method of manufacture thereof: US, 6286498[P]. 2001-09-11.
[11] Sung C M. Brazed diamond tools and methods for making: US, 6679243 [P]. 2004-01-20.
[12] Sung J C. Diamond tools with diamond grits set in a predetermined pattern[C]//Materials Science Forum. 2007, 534-536: 1101-1104.
[13] Wang C, Zhou Y, Zhang F, et al. Interfacial microstructure and performance of brazed diamond grits with Ni-Cr-P alloy[J]. Journal of Alloys and Compounds, 2009, 476(1): 884-888.
[14] Ham J O, Chung J H, Jung S K, et al. Interfacial behaviors of vacuum brazed joint between diamond grit and Ni-13Sn-28Cr filler alloy[J]. Advanced Materials Research, 2013, 705(6): 132-142.
[15] Chen Y, Fu Y, Su H, et al. The effects of solder alloys on the morphologies and mechanical properties of brazed diamond grits[J]. International Journal of Refractory Metals and Hard Materials, 2014, 42(10): 23-29.
[16] Huang S F, Tsai H L, Lin S T. Effects of brazing route and brazing alloy on the interfacial structure between diamond and bonding matrix [J]. Materials Chemistry and Physics, 2004, 84(2): 251-258.
[17] Hsieh Y Z, Lin S T. Diamond tool bits with iron alloys as the binding matrices[J]. Materials Chemistry and Physics, 2001, 72(2): 121-125.
[18] Sung J C, Sung M. The brazing of diamond[J]. International Journal of Refractory Metals and Hard Materials, 2009, 27(2): 382-393.
[19] 卢金斌, 张旺玺, 张雷, 等. 添加石墨对Ni-Cr合金保护气氛钎焊金 刚石磨粒界面组织的影响[J]. 机械工程学报, 2014, 50(4): 80-84. Lu Jinbin, Zhang Wangxi, Zhang Lei, et al. Effect on microstructure for adding graphite to Ni-Cr alloy wher brazing diamond abrasive in controlled atmosphere[J]. Journal of Mechanical Engineering, 2014, 50 (4): 80-84.
[20] 赵彬, 贺亚勋, 卢金斌, 等. 添加Cu粉对Ni-Cr合金真空钎焊金刚石 磨粒界面组织的影响[J]. 中原工学院学报, 2014, 25(3): 8-10. Zhan Bin, He Yaxun, Lu Jinbin, et al. Effect of microstructure of vacuum brazing diamond abrasive with Ni- Cr alloy added copper powder[J]. Journal of Zhongyuan University of Technology, 2014, 25 (3): 8-10.
[21] Hsieh Y C, Lin S T. Microstructural development of Cu-Sn-Ti alloys on graphite[J]. Journal of Alloys and Compounds, 2008, 466(1): 126- 132.
[22] Li W C, Lin S T, Liang C. Interfacial segregation of Ti in the brazing of diamond grits onto a steel substrate using a Cu-Sn-Ti brazing alloy [J]. Metallurgical and Materials Transactions A, 2002, 33(7): 2163- 2172.
[23] Khalid F, Klotz U, Elsener H R, et al. On the interfacial nanostructure of brazed diamond grits[J]. Scripta Materialia, 2004, 50(8): 1139-1143.
[24] Klotz U E, Liu C, Khalid F A, et al. Influence of brazing parameters and alloy composition on interface morphology of brazed diamond[J]. Materials Science and Engineering A, 2008, 495(1): 265-270.
[25] Buhl S, Leinenbach C, Spolenak R, et al. Failure mechanisms and cutting characteristics of brazed single diamond grains[J]. The International Journal of Advanced Manufacturing Technology, 2013, 66 (5-8): 775-786.
[26] Suzumura A, Yamazaki T. Brazing- filler material and method for brazing diamond: US, 6889890[P]. 2005-05-10.
[27] Yamazaki T, Suzumura A. Reaction products at brazed interface between Ag- Cu- V filler metal and diamond (111) [J]. Journal of Materials Science, 2006, 41(19): 6409-6416.
[28] 武志斌, 肖冰. 金刚石与金属基体钎焊机理的研究[J]. 工具技术, 2000, 34(11): 6-8. Wu Zhibin, Xiao Bing. Research on mechanism of brazing diamond to metal-base[J]. Tool Engineering, 2000, 34(11): 6-8.
[29] Sun F, Feng J, Li D. Bonding of CVD diamond thick films using an Ag-Cu-Ti brazing alloy[J]. Journal of Materials Processing Technology, 2001, 115(3): 333-337.
[30] 李丹, 孙文山. Ag-Cu-Ti钎料在金刚石表面的润湿状况[J]. 哈尔滨 理工大学学报, 2000, 5(3): 101-104. Li Dan, Sun Wenshan. Infiltration of Ag-Cu-Ti brazing on diamond [J]. Journal Harbing University Science & Techology, 2000, 5(3): 101-104.
[31] 关砚聪, 陈玉全, 姚德明. Ag-Cu-Ti钎料钎焊单晶金刚石磨粒的研 究[J]. 金刚石与磨料磨具工程, 2005, 25(3): 23-25. Guan Yancong, Chen Yuquan, Yao Deming. Study on soldering singlecrystal diamond abrasive with Ag-Cu-Ti solder[J]. Diamond & Abrasives Engineering, 2005, 25(3): 23-25.
[32] 卢金斌, 徐九华. Ag-Cu-Ti钎焊金刚石的界面结构及热应力分析 [J]. 稀有金属材料与工程, 2009, 38(4): 642-646. Lu Jinbin, Xu Jiuhua. Interface microstructure and thermal stress of diamond brazing with Ag-Cu-Ti filler[J]. Rare Metal Materials and Engineering, 2009, 38(4): 642-646.
[33] Klotz U, Khalid F, Elsener H R. Nanocrystalline phases and epitaxial interface reactions during brazing of diamond grits with silver based Incusil-ABA alloy[J]. Diamond and Related Materials, 2006, 15(10): 1520-1524.
[34] 张凤林, 周玉梅, 付凯旋, 等. Cr、Ti金属粉改善Ag-Cu-Zn合金对金 刚石的钎焊性能研究[J]. 金刚石与磨料磨具工程, 2007, 27(3): 22- 25. Zhang Fenglin, Zhou Yumei, Fu Kaixuan, et al. Adding Cr/Ti metal powder to improve brazing performance of Ag-Cu-Zn alloy to diamond [J]. Diamond & Abrasives Engineering, 2007, 27(3): 22-25.
[35] Wulf E, Bachmann H, Möhwald K, et al. The influence of brazing temperature and surface roughness on the wettability of reactive brazing alloys[J]. International Journal of Materials Research, 2014, 105(3): 240-248.
[36] 马伯江, 徐鸿钧, 傅玉灿, 等. 两种钎焊金刚石工具微观结构的对比 分析[J]. 机械工程材料, 2006, 29(7): 10-13. Ma Bojiang, Xu Hongjun, Fu Yucan, et al. Microstructure of brazed diamond tools made by two different techniques[J]. Materials for Mechanical Engineering, 2006, 29(7): 10-13.
[37] Chen Y, Xu H, Fu Y, et al. Effect of brazing atmospheres on interfacial microstructure between diamond grits and brazing alloy[J]. Journal of Nanjing University of Aeronautics and Astronautics, 2009, 25(4): 248-253.
[38] Buhl S, Leinenbach C, Spolenak R, et al. Microstructure, residual stresses and shear strength of diamond-steel-joints brazed with a Cu- Sn- based active filler alloy[J]. International Journal of Refractory Metals and Hard Materials, 2012, 30(1): 16-24.
[39] 钟如涛, 秦应雄, 唐霞辉, 等. 金刚石颗粒-金属粉末的CO2激光烧结 机理研究[J]. 金刚石与磨料磨具工程, 2009, 29(4): 18-23. Zhong Rutao, Qin Yingxiong, Tang Xiahui, et al. Study on CO2 laser sintering for the mixture of metallic powder and diamond grits[J]. Diamond & Abrasives Engineering, 2009, 29(4): 18-23.
[40] 马伯江, 徐鸿钧. 高频感应钎焊镀钛金刚石界面特征的研究[J]. 金刚 石与磨料磨具工程, 2007, 27(3): 1-3. Ma Bojiang, Xu Hongjun. A study on the interfacial characteristic of Ti-coated diamond brazed by high-frequency induction[J]. Diamond & Abrasives Engineering, 2007, 27(3): 1-3.
[41] 李文杰, 肖冰, 段端志, 等. 铜基预钎焊金刚石锯片的界面分析及其 性能研究[J]. 金刚石与磨料磨具工程, 2014, 34(2): 44-47. Li Wenjie, Xiao Bing, Duan Duanzhi, et al. Interface analysis and performance evaluation of the Cu- based pre- brazed diamond saw blade[J]. Diamond & Abrasives Engineering, 2014, 34(2): 44-47.
[42] Duan D Z, Xiao B, Wang B, et al. Microstructure and mechanical properties of pre- brazed diamond abrasive grains using Cu- Sn- Ti alloy[J]. International Journal of Refractory Metals and Hard Materials, 2015, 48(1): 427-432.
文章导航

/