|
|
Research progress on sand particle erosion-A corrosion alternative laboratory test method |
LUO Chen, LI Haiyang, CUI Yongjing, SUN Zhihua, TANG Zhihui |
AECC Key Laboratory on Advanced Corrosion and Protection for Aviation Materials, AECC Beijing Institute of Aeronautical Materials, Beijing 100095, China |
|
|
Abstract: Compressor blades and fan blades of aero engine encounter the blasting load from sand particles during service, as well as the influence of temperature, humidity and air pollution. In this paper, test methods related to sand environment and sand particle erosion are investigated, with emphasis on the common and difference of these methods using high speed sand stream to impact on samples. Gas jet test is chosen as a proper method to carry out erosion test and research for compressor blade and fan blade. An erosion method is designed according to the sand composition and particle size listed in GJB 241A-2010, GJB 242A- 2018. Sand feeding rate and testing time are controlled so as to meet the sand mass loads of compressor blade and fan blade in real service. The sand mass load is equivalent to the sand blast environment for aero engine in 1 year. Sand particle erosion testing and GJB 150.11A-2009 salt fog testing are carried out alternatively so that the testing scheme is closer to real service condition. Such methods may provide a technique foundation for aero engine compressor blade and fan blade to establish damage evolution rules and models considering the effect of corrosion environment and erosion load.
|
Received: 14 July 2021
|
|
|
|
[1] Henderson R E, Hennecke D K.Erosion corrosion and foreign object damage effects in gas turbines, ADA289820[R].Rotterdam:ADA, 1998.
[2] 何光宇, 李应红, 柴艳, 等.航空发动机压气机叶片砂尘冲蚀防护涂层关键问题综述[J].航空学报, 2015, 36(6):1733-1743.
[3] 卢言利, 潘家亮, 张拴勤, 等.高原环境因素对涂层自然老化性能的影响[J].装备环境工程, 2011, 8(2):37-41.
[4] 张燕, 李颖, 奚愚生, 等.海洋大气环境下高耐候性涂层体系的研究[J].装备环境工程, 2012, 9(4):74-78.
[5] Yang X H, He Q, Mamtimin A, et a1.A field experiment on dust emission by wind erosion in the Taklimakan des-ert[J].Acta Meteorologica Siniea, 2012, 26(2):241-249.
[6] Wang X M, Zhang C X, Wang H T, et a1.The signifi-cance of Gobi desert surfaces for dust emissions in China:An experimental study[J].Environmental Earth Sciences, 2011, 64(4):1039-1050.
[7] Yang X H, He Q, Mamtimin A, et a1.Near-surface sanddust horizontal flux in Taizhong-The hinterland of the Taklimakan desert[J].Journal of Arid Land, 2013, 5(2):199-206.
[8] Pfledderer L, Pepi M.Sand erosion test method for DOD unique environments[C]//Tri-Service Corrosion Confer-ence.Aberdeen:Army Research Laboratory, 2008:1-24.
[9] Pepi M, Squillacioti R, Pfledderer L, et al.Solid particle erosion testing of helicopter rotor blade materials[J].Jour-nal of Failure Analysis and Prevention, 2012, 12(1):96-108.
[10] Chen K Y, Bielawski M.Ab initio study on fracture toughness of Ti0.75X0.25C ceramics[J].Journal of Material Science, 2007, 42(23):9713-9716.
[11] Ashrafrizadeh H, Ashrafrizadeh F.A numerical 3D simu-lation for prediction of wear caused by solid particle im-pact[J].Wear, 2012, 276-277:75-84.
[12] Bielawski M, Beres W.FE modelling of surface stress in erosion-resistant coatings under single particle impact[J].Wear, 2007, 267:167-175.
[13] 刘道新, 奚运涛.离子辅助电弧沉积ZrN梯度涂层抗固体粒子冲蚀行为研究[J].航空材料学报, 2010, 30(4):31-37.
[14] 张沙, 龚烈航.前混合磨料水射流切割脆性材料研究[J].润滑与密封, 2011, 36(3):97-104.
[15] Alessio G D, Nagy D.Performance of erosion resistant coatings for compressor airfoils[J].Journal of the Canadi-an Ceramic Society, 1994, 63(1):59-63.
[16] 李慧艳, 方月华, 肖葵, 等.干热大气环境中涂层材料失效行为研究进展[J].科技导报, 2012, 30(34):76-79.
[17] 郝负洪, 邢永明, 杨诗婷, 等.风沙环境下钢结构表面涂层冲蚀行为与侵蚀机理研究[J].摩擦学学报, 2010, 30(1):26-31.
[18] 郝负洪, 李永.风沙环境下钢结构涂层低角度冲蚀特性研究[J].摩擦学学报, 2013, 33(4):345-348.
[19] 郝负洪, 邢永明, 杨诗婷, 等.风沙环境下钢结构涂层的冲蚀磨损力学性能研究[J].应用力学学报, 2013, 30(3):350-355.
[20] 张永, 黄超, 刘召, 等.挟沙风作用下风力机叶片涂层冲蚀特性研究[J].材料导报, 2016, 30(5):95-99.
[21] 张翼飞, 何光宇, 王学德, 等.航空发动机叶片TiN/Ti涂层基体冲蚀响应数值模拟[J].表面技术, 2015, 44(7):81-85
[22] 曹鑫, 何卫锋, 何光宇, 等.DLC、TiN涂层对TC4钛合金抗砂尘冲蚀性能的影响[J].中国表面工程, 2016, 29(4):60-67.
[23] 曹鑫, 王冠, 何卫锋, 等.TC4钛合金与多层TiN/Ti涂层的砂尘冲蚀损伤试验[J].航空动力学报, 2016, 31(9):2218-2225.
[24] 孙彦华.压气机常用马氏体不锈钢冲蚀及盐雾-冲蚀性能研究[D].哈尔滨:哈尔滨工程大学, 2010.
[25] 刘雪键, 彭文山, 刘少通, 等.含砂海水对40Cr钢加速冲刷腐蚀性能影响[J].装备环境工程, 2019, 16(3):9-16.
[26] 井勇智, 金国, 李昕瑶.海洋工况下航空发动机冷端叶片的冲蚀损伤与防护概述[J].装备环境工程, 2021,18(6):17-21.
[27] 张昭, 唐虎, 成竹.军用飞机实验室气候环境试验项目分析[J].装备环境工程, 2017,14(10):87-91.
[28] 马志宏, 李金国, 张景飞.军用装备砂尘环境试验技术[J].装备环境工程, 2007, 4(6):30-33.
[29] 马志宏, 汪浚.砂尘环境中军用装备磨损腐蚀进展的研究[J].腐蚀科学与防护技术, 2005, 17(2):112-115.
[30] Schell J D, Hein G, Mendez M, et a1.Erosion durability improvement of T64 engine for military heIicopters[C]//American Helicopter Society 60th Annual Forum.Virgin-ia:American Helicopter Society, 2004:7-10.
[31] 霍武军, 孙护国.海航发动机压气机叶片腐蚀与防护措施[J].航空维修与工程, 2002, 6:39-41.
[32] Evans A G, Gulden M E, Rosenblatt M.Impact damage in brittle materials in the elastic-plastic response regime[J].Proceedings of the Royal Society of London.Series A.Mathematical and Physical Sciences, 1978, 361(1706):343-365.
[33] Hockey B J, Wiederhorn S M, Johnson H.Erosion of brittle materials by solid particle impact[M]//Flaws and Testing.Boston:Springer, 1978:379-402.
[34] 吴小梅, 商晓宇.三种不锈钢材料抗砂尘冲蚀性能研究[J].航空材料学报, 2012, 32(3):68-72.
[35] 吴小梅, 李伟光, 陆峰.压气机叶片抗冲蚀涂层的研究及应用进展[J].材料保护, 2007, 40(10):54-57.
[36] 王坤, 吴敬权, 邓培昌, 等.管流式冲刷腐蚀实验装置的设计及性能试验[J].装备环境工程, 2019,16(12):56-60.
[37] 孙炜, 范金娟.聚氨酯涂层固体颗粒冲蚀研究进展[J].装备环境工程, 2020,17(12):67-75. |
[1] |
ZHANG Huanhuan, LIU Wenchao, TIAN Haoliang, WEI Shicheng, LIANG Yi. Preparation and properties of self propagating anti-corrosion and wear-resistant coating on inner wall of equipment copper pipe[J]. Science & Technology Review, 2022, 40(5): 28-33. |
[2] |
LI Yonghong, SHAO Xiaofeng, HU Tianqi. Environmental spectrum life prediction of Q345 carbon steel coating electrical cabinet of Beijing-Guangzhou high speed railway[J]. Science & Technology Review, 2022, 40(5): 138-148. |
[3] |
LUO Chen, SUN Zhihua, LIU Ming, PAN Qiao. Analysis of aeronautical materials' and products' demand for environmental testing data resource[J]. Science & Technology Review, 2021, 39(9): 17-23. |
[4] |
WANG Qiang, ZHENG Riheng, CHEN Maozhang. Development and innovation of aeroengine science and technology[J]. Science & Technology Review, 2021, 39(3): 59-70. |
[5] |
ZHANG Song, BAI Keqiang, DAN Zhihong, QIAN Qiumeng, LIU Lei. Research status of engine air intake pressure control based on ESO[J]. Science & Technology Review, 2021, 39(11): 109-117. |
[6] |
HAO Binbin, LU Jinzhi, LI Jun, WANG Guoxin, LAN Xiaoping, CHEN Jianjiang, WU Xin. Domain-specific modeling approach for model-based systems engineering in aero-engine development[J]. Science & Technology Review, 2019, 37(7): 88-95. |
|
|
|
|